Subversion Repositories configs

Rev

Details | Last modification | View Log | RSS feed

Rev Author Line No. Line
4 - 1
# $XdotOrg: Xaccess,v 1.3 2000/08/17 19:54:17 cpqbld Exp $
2
# $Xorg: Xaccess,v 1.3 2000/08/17 19:54:17 cpqbld Exp $
3
# $XFree86: xc/programs/xdm/config/Xaccess,v 1.4 2003/07/09 15:27:40 tsi Exp $
4
#
5
# Access control file for XDMCP connections
6
#
7
# To control Direct and Broadcast access:
8
#
9
#	pattern
10
#
11
# To control Indirect queries:
12
#
13
# 	pattern		list of hostnames and/or macros ...
14
#
15
# To use the chooser:
16
#
17
#	pattern		CHOOSER BROADCAST
18
#
19
# or
20
#
21
#	pattern		CHOOSER list of hostnames and/or macros ...
22
#
23
# To define macros:
24
#
25
#       %name		list of hosts ...
26
#
27
# To control which addresses xdm listens for requests on:
28
#
29
#	LISTEN		address [list of multicast groups ... ]
30
#
31
# The first form tells xdm which displays to respond to itself.
32
# The second form tells xdm to forward indirect queries from hosts matching
33
# the specified pattern to the indicated list of hosts.
34
# The third form tells xdm to handle indirect queries using the chooser;
35
# the chooser is directed to send its own queries out via the broadcast
36
# address and display the results on the terminal.
37
# The fourth form is similar to the third, except instead of using the
38
# broadcast address, it sends DirectQuerys to each of the hosts in the list
39
# The fifth form tells xdm which addresses to listen for incoming connections
40
# on.  If present, xdm will only listen for connections on the specified
41
# interfaces and/or multicast groups.
42
#
43
# In all cases, xdm uses the first entry which matches the terminal;
44
# for IndirectQuery messages only entries with right hand sides can
45
# match, for Direct and Broadcast Query messages, only entries without
46
# right hand sides can match.
47
#
48
 
49
*					#any host can get a login window
50
 
51
#
52
# To hardwire a specific terminal to a specific host, you can
53
# leave the terminal sending indirect queries to this host, and
54
# use an entry of the form:
55
#
56
 
57
#terminal-a	host-a
58
 
59
 
60
#
61
# The nicest way to run the chooser is to just ask it to broadcast
62
# requests to the network - that way new hosts show up automatically.
63
# Sometimes, however, the chooser can't figure out how to broadcast,
64
# so this may not work in all environments.
65
#
66
 
67
#*		CHOOSER BROADCAST	#any indirect host can get a chooser
68
 
69
#
70
# If you'd prefer to configure the set of hosts each terminal sees,
71
# then just uncomment these lines (and comment the CHOOSER line above)
72
# and edit the %hostlist line as appropriate
73
#
74
 
75
#%hostlist	host-a host-b
76
 
77
#*		CHOOSER %hostlist	#
78
 
79
#
80
# If you have a machine with multiple network interfaces or IP addresses
81
# you can control which interfaces accept XDMCP packets by listing a LISTEN
82
# line for each interface you want to listen on.  You can additionally list
83
# one or more multicast groups after each address to listen on those groups
84
# on that address.
85
#
86
# If no LISTEN is specified, the default is the same as "LISTEN *" - listen on
87
# all unicast interfaces, but not for multicast packets.  If any LISTEN lines
88
# are specified, then only the listed interfaces will be listened on.
89
#
90
# IANA has assigned FF0X:0:0:0:0:0:0:12B as the permanently assigned
91
# multicast addresses for XDMCP, where X in the prefix may be replaced
92
# by any valid scope identifier, such as 1 for Node-Local, 2 for Link-Local,
93
# 5 for Site-Local, and so on.  The default is equivalent to the example shown
94
# here using the Link-Local version to most closely match the old IPv4 subnet
95
# broadcast behavior.
96
#
97
# LISTEN		* ff02:0:0:0:0:0:0:12b
98
 
99
# This example shows listening for multicast on all scopes up to site-local
100
#
101
# LISTEN	* ff01:0:0:0:0:0:0:12b ff02:0:0:0:0:0:0:12b ff03:0:0:0:0:0:0:12b ff04:0:0:0:0:0:0:12b ff05:0:0:0:0:0:0:12b