| 4 |
- |
1 |
# -*- text -*-
|
|
|
2 |
#
|
|
|
3 |
# $Id$
|
|
|
4 |
|
|
|
5 |
#
|
|
|
6 |
# The "linelog" module will log one line of text to a file.
|
|
|
7 |
# Both the filename and the line of text are dynamically expanded.
|
|
|
8 |
#
|
|
|
9 |
# We STRONGLY suggest that you do not use data from the
|
|
|
10 |
# packet as part of the filename.
|
|
|
11 |
#
|
|
|
12 |
linelog {
|
|
|
13 |
#
|
|
|
14 |
# The file where the logs will go.
|
|
|
15 |
#
|
|
|
16 |
# If the filename is "syslog", then the log messages will
|
|
|
17 |
# go to syslog.
|
|
|
18 |
filename = ${logdir}/linelog
|
|
|
19 |
|
|
|
20 |
#
|
|
|
21 |
# The Unix-style permissions on the log file.
|
|
|
22 |
#
|
|
|
23 |
# Depending on format string, the log file may contain secret or
|
|
|
24 |
# private information about users. Keep the file permissions as
|
|
|
25 |
# restrictive as possible.
|
|
|
26 |
permissions = 0600
|
|
|
27 |
|
|
|
28 |
#
|
|
|
29 |
# The default format string.
|
|
|
30 |
format = "This is a log message for %{User-Name}"
|
|
|
31 |
|
|
|
32 |
#
|
|
|
33 |
# This next line can be omitted. If it is omitted, then
|
|
|
34 |
# the log message is static, and is always given by "format",
|
|
|
35 |
# above.
|
|
|
36 |
#
|
|
|
37 |
# If it is defined, then the string is dynamically expanded,
|
|
|
38 |
# and the result is used to find another configuration entry
|
|
|
39 |
# here, with the given name. That name is then used as the
|
|
|
40 |
# format string.
|
|
|
41 |
#
|
|
|
42 |
# If the configuration entry cannot be found, then no log
|
|
|
43 |
# message is printed.
|
|
|
44 |
#
|
|
|
45 |
# i.e. You can have many log messages in one "linelog" module.
|
|
|
46 |
# If this two-step expansion did not exist, you would have
|
|
|
47 |
# needed to configure one "linelog" module for each log message.
|
|
|
48 |
|
|
|
49 |
#
|
|
|
50 |
# Reference the Packet-Type (Access-Request, etc.) If it doesn't
|
|
|
51 |
# exist, reference the "format" entry, above.
|
|
|
52 |
reference = "%{%{Packet-Type}:-format}"
|
|
|
53 |
|
|
|
54 |
#
|
|
|
55 |
# Followed by a series of log messages.
|
|
|
56 |
Access-Request = "Requested access: %{User-Name}"
|
|
|
57 |
Access-Reject = "Rejected access: %{User-Name}"
|
|
|
58 |
Access-Challenge = "Sent challenge: %{User-Name}"
|
|
|
59 |
|
|
|
60 |
#
|
|
|
61 |
# The log messages can be grouped into sections and
|
|
|
62 |
# sub-sections, too. The "reference" item needs to have a "."
|
|
|
63 |
# for every section. e.g. reference = foo.bar will reference
|
|
|
64 |
# the "foo" section, "bar" configuration item.
|
|
|
65 |
#
|
|
|
66 |
|
|
|
67 |
#
|
|
|
68 |
# Used if: reference = "foo.bar".
|
|
|
69 |
foo {
|
|
|
70 |
bar = "Example log. Please ignore"
|
|
|
71 |
}
|
|
|
72 |
|
|
|
73 |
#
|
|
|
74 |
# Another example:
|
|
|
75 |
# reference = "Accounting-Request.%{%{Acct-Status-Type}:-unknown}"
|
|
|
76 |
#
|
|
|
77 |
Accounting-Request {
|
|
|
78 |
Start = "Connect: [%{User-Name}] (did %{Called-Station-Id} cli %{Calling-Station-Id} port %{NAS-Port} ip %{Framed-IP-Address})"
|
|
|
79 |
Stop = "Disconnect: [%{User-Name}] (did %{Called-Station-Id} cli %{Calling-Station-Id} port %{NAS-Port} ip %{Framed-IP-Address}) %{Acct-Session-Time} seconds"
|
|
|
80 |
|
|
|
81 |
# Don't log anything for these packets.
|
|
|
82 |
Alive = ""
|
|
|
83 |
|
|
|
84 |
Accounting-On = "NAS %C (%{NAS-IP-Address}) just came online"
|
|
|
85 |
Accounting-Off = "NAS %C (%{NAS-IP-Address}) just went offline"
|
|
|
86 |
|
|
|
87 |
# don't log anything for other Acct-Status-Types.
|
|
|
88 |
unknown = ""
|
|
|
89 |
}
|
|
|
90 |
|
|
|
91 |
}
|