Subversion Repositories configs

# Plustek-SANE Backend configuration file

# For use with LM9831/2/3 based USB scanners

#

# each device needs at least two lines:

# - [usb] vendor-ID and product-ID

# - device devicename

# i.e. for Plustek (0x07B3) UT12/16/24 (0x0017)

# [usb] 0x07B3 0x0017

# device /dev/usbscanner

# or

# device libusb:bbb:ddd

# where bbb is the busnumber and ddd the device number

# make sure that your user has access to /proc/bus/usb/bbb/ddd

#

# additionally you can specify some options

# warmup, lOffOnEnd, lampOff

#

# For autodetection use

# [usb]

# device /dev/usbscanner

#

# or simply

# [usb]

#

# or if you want a specific device but you have no idea about the

# device node or you use libusb, simply set vendor- and product-ID

# [usb] 0x07B3 0x0017

# device auto

#

# NOTE: autodetection is safe, as it uses the info it got

#       from the USB subsystem. If you're not using the

#       autodetection, you MUST have attached that device

#       at your USB-port, that you have specified...

#

[usb]

#

# options for the previous USB entry

#

# switch lamp off after xxx secs, 0 disables the feature

# (can also be set via frontend)

option lampOff 300

# warmup period in seconds, 0 means no warmup, -1 means auto-warmup

# (can also be set via frontend)

option warmup -1

# 0 means leave lamp-status untouched, not 0 means switch off

# on sane_close

# (can also be set via frontend)

option lOffOnEnd 1

#

# options to tweak the image start-position

# (WARNING: there's no internal range check!!!)

#

# for the normal scan area

#

option posOffX 0

option posOffY 0

# for transparencies

option tpaOffX 0

option tpaOffY 0

# for negatives

option negOffX 0

option negOffY 0

#

# for setting the calibration strip position

# (WARNING: there's no internal range check!!!)

# -1 means use built in

# (can also be set via frontend)

option posShadingY -1

option tpaShadingY -1

option negShadingY -1

#

# to invert the negatives, 0 disables the feature

#

option invertNegatives 0

#

# to disable the internal sensor speedup function,

# 1 disables the feature

#

option disableSpeedup 0

#

# to save/restore coarse calibration data

# (can also be set via frontend)

option cacheCalData 0

#

# use alternate calibration routines

#

option altCalibration 0

#

# for skipping whole calibration step

#

option skipCalibration 0

#

# for skipping entire fine calibration step

# coarse calibration is done

#

option skipFine 0

#

# discard the result of the fine white calibration

#

option skipFineWhite 0

#

# some scanners have a dark calibration strip, in

# general this one should be used for calibration.

# As this could cause some trouble, this option

# overrides that and the dark calibration will be

# done by switching the lamp off

#

option skipDarkStrip 0

# for replacing the gain values found during coarse

# calibration

# (can also be set via frontend)

option red_gain   -1

option green_gain -1

option blue_gain  -1

# for replacing the offset values found during coarse

# calibration

# (can also be set via frontend)

option red_offset   -1

option green_offset -1

option blue_offset  -1

#

# for replacing the default lampoff settings, this

# works only for CIS devices like CanoScan LiDE20

# (can also be set via frontend)

option red_lampoff   -1

option green_lampoff -1

option blue_lampoff  -1

#

# for adjusting the default gamma values

# (can also be set via frontend)

option redGamma         1.0

option greenGamma       1.0

option blueGamma        1.0

option grayGamma        1.0

#

# to enable TPA (EPSON or UMAX, if autodetection fails)

# 0 means default behaviour as specified in the internal tables

# 1 means enable (needed for UMAX 3450)

option enableTPA 0

#

# model override functionality, currently only available for

# Mustek devices, using NSCs' vendor ID: 0x0400 and

# also their product ID: 0x1000 (LM9831) 0x1001 (LM9832)

#

# mov/PID    |    0x1000   |   0x1001

# ---------------------------------------

# 0 (default)| BearPaw1200 | BearPaw 2400

# 1          |   ignored   | BearPaw 1200

#

option mov 0

#

# and of course the device-name

#

# device /dev/usbscanner

device auto

#

# to define a new device, start with a new section:

# [usb]

#